Microcontroller Trace Support with UDE® Universal Debug Engine
In depth real-time debugging requires close interaction with the processor. Tracing shall provide a chronological picture of a system's inner workings - before or after a critical event - mainly to help analyzing a faulty program.
Function Profiling | Code Coverage | Execution sequence | Variable access | |
---|---|---|---|---|
Measurement | Amount of execution time for each function | Execution of code | Call hierarchy and execution time sequence | Memory changes |
Requirements | Code trace with tick information (Subroutine only possible) | Code trace without tick information | Code trace with tick information | Data trace with tick information |
Results | Graphical chart and reports of Profiling | Graphical chart and reports of Code Coverage | Graphical chart of Sequences | Graphical chart |
The Multi-core Debug Solution (MCDS) integrated on the Emulation Extension Chip (EEC) of Infineons AURIX and TriCore TC39xED, TC29xED, TC27xED is a powerful trace and event generation module. This new full-featured emulator onsilicon opens a new age of debugging capabilities. It allows to observe and control the running system in a very purposeful way. Elaborated filter mechanisms and a high visibility to the system internals (cores and busses) are the key features of AURIX and TriCore MCDS. To make use of them the MCDS has to be configured for each trace task using the Universal Emulation Configurator (UEC).
Infineon has also implemented an AURIX AURORA GigaBit Trace (AGBT) / Serial GigaBit Trace (SGBT) interface on the Emulation Device in order to further increase testability of the new TC49xED, TC39xED, TC29xED, TC27xED AURIX microcontroller with multicore architecture. Emulation Devices of PowerArchitecture derivatives as MPC57xx, SPC57xx, SPC58xx supports AURORA interface, too. As a result, the trace memory can be greatly enlarged by connecting external hardware, which in turn allows the management of high-end trace tasks with large amounts of data, for example code coverage.
However, a 2.5 GB/s AURORA interface requires correspondingly high-performance hardware for signal acquisition, signal conditioning and preprocessing on the target. Therefore, not only is a trace pod with AGBT interface available for the UAD3+ from PLS, but it can also be equipped with up to 4 GByte of external trace memory.
The UAD3+ allows the recording of real-time trace information via a high speed serial trace based interface.
- Support of AURORA based Trace protocols for Infineon AURIX and PowerArchitecture (Samtec ERF8 HS22, Samtec ERF8 HS34, additional customer specific trace connectors)
- Maximum of 4 lanes supported, maximum data rate per lane is 3.125 Gbit/s
- Trace memory scalable up to 4 GBytes
- Time-endless trace for a continuous tracing and observation.
The UAD2next allows the recording of real-time trace information via a high speed serial trace based interface.
- Support of AURORA based Trace protocols for Infineon AURIX and PowerArchitecture (Samtec ERF8 HS22, Samtec ERF8 HS34, additional customer specific trace connectors)
- Maximum of 2 lanes supported, maximum data rate per lane is 1.25 Gbit/s
- Trace memory scalable up to 512 MBytes
- Time-endless trace for a continuous tracing and observation.
STMicroelectronics has also implemented an Arm High Speed Serial Trace Port (HSSTP) interface via AURORA on the Cortex-R52 Stellar Devices. As a result, the trace memory can be greatly enlarged by connecting external hardware, which in turn allows the management of high-end trace tasks with large amounts of data, for example code coverage.
However, an AURORA interface requires correspondingly high-performance hardware for signal acquisition, signal conditioning and preprocessing on the target. Therefore, not only is a trace pod with HSSTP interface available for the UAD3+ from PLS, but it can also be equipped with up to 4 GByte of external trace memory.
The UAD3+ allows the recording of real-time trace information via a high speed serial trace based interface.
- Support of AURORA based Trace protocols (HSSTP) for Cortex-R52 Stellar (Samtec ERF8 HS40, additional customer specific trace connectors).
- Maximum of 4 lanes supported, maximum data rate per lane is 3.125 Gbit/s
- Trace memory scalable up to 4 GBytes
- Time-endless trace for a continuous tracing and observation.
The UAD2next allows the recording of real-time trace information via a high speed serial trace based interface.
- Support of AURORA based Trace protocols (HSSTP) for Cortex-R52 Stellar (Samtec ERF8 HS40, additional customer specific trace connectors).
- Maximum of 2 lanes supported, maximum data rate per lane is 1.25 Gbit/s
- Trace memory scalable up to 512 MBytes
- Time-endless trace for a continuous tracing and observation.
Hard real-time debugging requires close interaction with the processor. Tracing shall provide a chronological picture of a system inner working up to, starting from or in the vicinity an event, mainly to guide a human in understanding a faulty program. ETM and ETB were defined for this purpose and are available on the Arm derivatives.
CoreSight Trace Memory Controller (TMC) extends the CoreSight Embedded Trace Buffer (ETB) with Embedded Trace FIFO (ETF) and Embedded Trace Router (ETR). It can be used to capture trace using a 2-pin serial wire debug (SWD) as external trace as wells as the system memory as dynamic Random Access Memory (RAM) as on-chip trace. TMC is available on some Cortex-R52 derivatives and supported by Universal Debug Engine.
The Universal Debug Engine provides support for all Zynq-7000 (Cortex-A9) specific trace features:
- Instrumentation Trace Macrocell (ITM)
- Program Trace Macrocell (PTM)
- Fabric Trace Macrocell (FTM)
- Tracing of both Cortex-A9 cores in parallel.
UDE® reconstructs the time aligned program flow from captured trace data and presents it in the multicore aware trace window. For higher system analysis Code Coverage as well as function Profiling is available.
UDE® supports program trace, data trace, watchpoint trace, ownership trace via the Nexus interface. This function is currently available - in combination with the Universal Access Device 3+ - for the Power Architecture™ derivatives MPC55xx, MPC56xx, MPC57xx from NXP as well as SPC56x, SPC57x, SPC58x from STMicroelectronics.
A 2-bit, 4-bit or even 12-bit and 16-bit wide trace data port with up to 250 MHz clock frequency are supported, whereby up to 1 megasamples can be recorded. With a compression of the trace data direct by the trace hardware, this represents a multiple of machine commands. Moreover, every sample can contain eight additional external hardware signals. Recording of the samples takes place synchronously to the Nexus clock frequency. This enables an optimal use of the trace memory and application optimized timestamps.
ARC SmaRT Trace (SmaRT = Small Real-Time Trace) is a special debug feature of the ARC cores. The last 8 to 4096 origin and destination jump addresses and other flags can be saved in the SmaRT trace stream. Available flags are: User mode change, task change with RTOS, exception occurred, repetition of control flow, valid jump address.
Synopsys developed the SmaRT (Small Real Time Trace) feature to have a mighty trace protocol with a smaller footprint and with less power consumption. SmaRT does not deliver ticks or timestamp information. So these virtual ticks are added by UDE® (1 tick per instruction) to enable timing analysis like Execution Sequence Chart or Profiling.
UDE® restores the previous control flow according to the available trace information and enables trace analyses such as Code Coverage, Execution Sequence Chart, Profiling and Call Graph Analysis.
The trace stream can be exported as several output formats:
- Raw Trace Data - Binary Trace Data as Read From the Target
- UTF Trace Data in Binary Format - Universal Trace Format (UTF) in Binary Form
- UTF Trace Data in Text Format - Universal Trace Format (UTF) in Human Readable Form
- UTF Trace Data in HTML Format - Universal Trace Format (UTF) in Internet Browser Parsable Form
- UTF Trace Data as Value Change Dump - Produce a Value Change Dump (VCD) From Decoded Trace Data.
In the trace window shown trace information can be exported also as further output formats:
- TAB/SPACE separated Format - Columns from trace window as TAB/SPACE-separated text
- XML Format - Columns from trace window saved in XML style.